Teledex Pearl User Manual

Browse online or download User Manual for Phones Teledex Pearl. Teledex Pearl User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 8
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
PACKAGE CONTENTS
Check to be sure that you have all of the following components in
your package (see figure below) :
• Telephone base unit • Handset coil cord • User guide
• Handset • Line cord
INSTALLATION
1) Plug one end of the handset coiled cord into the handset. Plug
the other end of the cord into the handset jack located on the
left side of the phone base. (Refer to diagram on reverse.)
2) Place the handset in the handset cradle. Plug one end of the line
cord into the LINE jack on the back of your phone.
3) Plug the other end of the modular cord into the wall jack.
WALL MOUNTING
The Pearl telephone can easily be attached to a wall mount plate.
1) Remove the wall mount clip (located on the front of the
telephone, above the speaker grill) by firmly pushing upward
(toward the hook switch.)
2) Rotate the clip 180 degrees, so that the side with the protruding
edge is towards the top of the telephone. This edge will help
hold the handset on the cradle.
3) Place the handset in the handset cradle.
4) Connect the line cord into the LINE jack on the back of your
phone. Route the line cord through channel on the bottom of
the telephone. Connect the other end of the line cord to the
jack on the wall mount plate.
5) Slip the phone onto the wall plate; slide the telephone down
so it is firmly in place.
USING THE DATA PORT
The data port is located on the right hand side of the telephone. Use
this jack to connect a computer or fax machine in parallel to the
same phone line to which the telephone is connected.
ADJUSTING THE RINGER VOLUME
Your Pearl telephone has two ringer volume levels: “Low” and “High.”
To adjust the ringer volume, slide the ringer volume switch (located
on the backside of the telephone) to the desired level.
HANDSET VOLUME CONTROL
There are three (3) volume levels for the handset volume. To increase
or decrease the handset volume, slide the handset volume switch
(located on the right hand side of the telephone) to the desired setting.
PLACING AND ANSWERING CALLS
To make a call, pick up the handset. When you hear the dial tone,
dial the desired phone number. To answer an incoming call, pick up
the handset. To end a call, place the handset back on the base.
USING REDIAL
The redial function allows you to redial the last dialed number.
Pick up the handset and press the REDIAL key. The number will be
dialed automatically.
USING FLASH
Flash supports custom calling services, such as call waiting. For
example, if you have subscribed to call waiting, press FLASH to answer
an incoming call, without disconnecting the current call. Press FLASH
again to return to the first call.
PROGRAMMING FLASH TIMING
NOTE – The following procedure should only be attempted by a
trained technician. If you are unsure of your ability to carry out this
procedure, please refer the procedure to such a trained technician.)
The flash timing on the Pearl phone can be set at 100ms, 300ms or
600ms, by using a jumper. This jumper is located under a hidden
cover at the top of the telephone. To access this cover, remove the
plastic overlay, undo the two screws, and remove the cover.
1) For 100ms flash, set the jumper at location
J100.
2) For 300ms flash, set the jumper at location J300.
3) For 600ms flash, set the jumper at location J600.
PROGRAMMING GUEST SERVICE KEYS
Follow these steps to program a number into one of the three memo-
ry locations, for one-touch access to guest services, or for accessing
special PBX/Centrex services or features. Each memory location can
store up to sixteen (16) digits.
1) Lift the handset, listen for dial tone, and press the STORE key
(For key location, refer to diagram on reverse.)
2) Press the guest service key where you would like the number
to be stored.
3) Using the dial pad, enter the number you wish to store (up
to 24 digits in length.)
4) Press the STORE key again to complete. Repeat as necessary for
subsequent guest service keys.
DIALING A STORED NUMBER
Pick up the handset, wait for a dial tone, then press the desired
memory (guest service) key. The telephone will automatically dial the
stored number.
MESSAGE WAITING
The message waiting indicator flashes to indicate that there is a
message waiting. Consult your system administrator or service
provider for instructions on how to access these messages.
PEARL
Guestroom Telephone
Users Guide (Pan Euro)
PACKAGE
CONTENTS
BASE UNIT HANDSET
COIL CORD
LINE CORD USER GUIDE
Page view 0
1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Users Guide (Pan Euro)

PACKAGE CONTENTSCheck to be sure that you have all of the following components inyour package (see figure below) :• Telephone base unit • Handset coil

Page 2 - WALL MOUNTING

CARE AND MAINTENANCEYour Pearl telephone has been designed to provide years of troublefree service. To ensure its longevity, please follow these main

Page 3 - Guestroom Speakerphone

PACKAGE CONTENTSCheck to be sure that you have all of the following components inyour package (see figure below) :• Telephone base unit • Handset coil

Page 4

CARE AND MAINTENANCEYour Pearl S telephone has been designed to provide years of troublefree service. To ensure its longevity, please follow these mai

Page 5 - Users Guide

PACKAGE CONTENTSCheck to be sure that you have all of the following components inyour package (see figure below) :• Telephone base unit • Handset coil

Page 6

REQUIREMENTS OF PART 68 - FCC RULESThis device has been granted a registration number by the Federal Communications Commission,under Part 68 rules and

Page 7

PACKAGE CONTENTSCheck to be sure that you have all of the following components inyour package (see figure below) :• Telephone base unit • Handset coil

Page 8

REQUIREMENTS OF PART 68 - FCC RULESThis device has been granted a registration number by the Federal Communications Commission,under Part 68 rules and

Comments to this Manuals

No comments